Bucket Lip Shroud with LS3001600J Marking – Aftermarket Replacement

Short Description

This aftermarket bucket lip shroud is photographed with the marking LS3001600J, while the supplied enquiry reference is WS3001600J. The relationship between these references requires confirmation before ordering. The pictured part has a broad curved wear face, a raised rear mounting section and a visible circular opening. For replacement sourcing, provide the existing shroud marking, bucket details, mounting photographs and measured interfaces so that the required part and supply scope can be checked.

Full Description

This aftermarket bucket lip shroud is presented for replacement enquiries from equipment-parts distributors, importers, maintenance businesses, mining operators and earthmoving contractors. The photographed part carries the marking LS3001600J. The enquiry reference supplied for this listing is WS3001600J. These two references have not been established as interchangeable. Please identify the reference required for your order and provide supporting bucket information before the product specification is finalized.

The photograph shows a yellow component with a broad wear body, a curved front edge and a raised mounting section extending toward the rear. A circular opening is visible near the rounded end of this section, with an additional raised eye-shaped feature nearer the middle. The LS3001600J marking is visible on the side shoulder. These details help with visual comparison; measurements and photographs of the underside are needed to check the actual mating surfaces.

Bucket lip shrouds provide a replaceable wear surface along exposed sections of a bucket lip. The catalogue reference LS300-1600J appears within Hensley’s J-Bolt lip-shroud range and offers a starting point for investigating the photographed marking. This catalogue association does not establish that the pictured component fits a particular base or bucket. The mounting geometry, lip profile and retention arrangement must be checked against the assembly being repaired.

Applications for a correctly selected lip shroud include bucket maintenance in mining, quarrying and abrasive material handling. Suitability depends on the bucket configuration, the material being handled and the approved replacement specification. Discuss these operating conditions when requesting a quotation. A machine model alone cannot establish fitment where buckets, lips or wear-protection systems have been changed during the equipment’s service life.

For compatibility review, supply clear photographs of the old shroud from above, below and both sides. Include close-up photographs of its markings, the exposed bucket lip, the mounting base and the retaining arrangement. Provide measured overall dimensions, mounting openings, lip thickness and relevant interface distances, preferably on a drawing. If the old part is heavily worn, an unworn sample or an approved drawing will provide a more useful reference than the worn outside profile.

Distributors and importers should identify whether the enquiry concerns a single replacement, repeat stock orders or a wider bucket-maintenance package. Maintenance companies and contractors should also state the machine model, bucket manufacturer, bucket serial number if available, and the installation position. Keep centre, left-hand and right-hand shroud requirements separate when preparing a purchasing list, and confirm each required reference against its own mounting details.

Before ordering, agree the product identification, dimensions, material requirements, inspection documents and exact supply scope in writing. Confirm any required mounting hardware separately, together with quantity, packing requirements, destination and requested delivery date. Price, availability, packaging and lead time should be established in the quotation. Send both the enquiry reference WS3001600J and the photographed marking LS3001600J so the identification difference can be resolved before an order is accepted.

Key Features

• Aftermarket replacement classification for parts procurement.

• Broad wear body with a curved front edge, as photographed.

• Raised rear mounting section visible in the supplied image.

• Circular opening visible near the rounded rear end.

• LS3001600J marking visible on the photographed component.

• Yellow exterior finish shown in the product photograph.

Compatible Machine Models

Compatibility must be checked by the bucket lip, mounting base and retention arrangement. Provide the machine model together with bucket identification and interface measurements for review.

Reference Part Numbers

Photographed marking: LS3001600J. Catalogue writing found during identification research: LS300-1600J. The supplied enquiry reference WS3001600J requires separate confirmation; no interchangeability between WS and LS references is established.

Applications

• Bucket lip wear-protection replacement enquiries.

• Bucket maintenance for mining and quarry operations, subject to configuration checks.

• Abrasive material-handling applications, subject to specification review.

• Replacement-parts sourcing for distributors, importers, repair businesses and contractors.